Category Archives: concrete mender

Use Roadware 10 Minute Concrete Mender to repair and re-bond delaminated concrete slabs.

Use Roadware 10 Minute Concrete Mender to repair and re-bond delaminated concrete slabs.

Roadware delimanition repairs are featured in the July 2008 issue of Concrete International. This is the official publication of the American Concrete Institute. The article was written by Nelson Tonet, President of Express Polymers and a Roadware distributor.

ABSTRACT
“Delaminations in concrete floor slabs can be difficult to repair in a cost-effective and timely manner. A newly developed product (Roadware 10 Minute Concrete Mender™) that uses a two-part hybrid polyurethane with a viscosity similar to water can significantly reduce the difficulty of performing delamination repairs by easily flowing up to 10 ft (3 m) from an injection point and penetrating deep into concrete surfaces. The product also speeds up repair by setting in only 10 minutes, allowing the repair to be checked by sounding only 30 minutes after product placement.”

View full article in PDF format Delamination Repairs PDF

Here is a Roadware synopsis.

Roadware 10 Minute Concrete Mender™ is an excellent choice for repairing concrete slab delaminations. The very low viscosity of less then 8 cps and the exclusive Microdoweling™ penetration properties of the material allow it to flow deep into delaminated concrete voids. The Concrete Mender will restore aggregate interlock and will allow dynamic load transfer under heavy traffic. The expense and mess of pressure injection with epoxy can be avoided.

Two methods of repair have been successful. The first involved dry diamond drilling a 2 or 3 inch (5-8 cm) diameter hole into the concrete slab down to the delamination. Dust is removed with a shop vacuum. Roadware 10 Minute Concrete Mender is poured or pumped into the void. Only one or two inches (3-5 cm) of head pressure is required to push the material as far as 10 ft (3 m) into the delamination. When the material backs up to the top of the hole and the void is filled, silica sand is added and the hole is filled flush with the surface. Soundings are made with a hammer to verify the delamination is repaired in about 30 minutes after application.

Click here to see how Nelson Tonet repairs delaminated concrete slabs.

Another method is to drill multiple 3/8 inch (1 cm) holes into the concrete down to the delamination. Remove dust with a shop vacuum and inject pre-mixed Roadware 10 Minute Concrete Mender™ with a syringe tipped with a rubber gasket. With this method, you can actually see the material exit the adjacent hole and verify the material is filling the delaminated area. After filling, the holes are blended into the surrounding concrete with silica sand and Concrete Mender or re-drill 1/4″ (5 mm) deep and fill with a color matching concrete mortar.

See the movie:

Both methods will yield good results and are more cost effective than epoxy injection.

See actual bridge deck repairs in PA on Google Maps.

See actual bridge deck repairs on Google Maps.

Google has spent the last few years mapping and photographing roads all over the world. If you know where to look, you can see actual concrete repairs with Roadware 10 Minute Concrete Mender™

The Google Map photo below shows actual bridge deck repairs with Roadware 10 Minute Concrete Mender™ on Interstate 279 in Pittsburgh, PA.  See all the lighter colored spots? Each one is a hole or spall filled with Roadware 10 Minute Concrete Mender™. The repairs here are over three years old. Thank you Roadware distributor, Express Polymers, Inc., in the Pittsburgh area for sending this project in.


View Larger Map

Roadware Commercial for World of Concrete 2011

The World of Concrete 2011 in Las Vegas is next month, January 17-21. Roadware will be in Booth S11847. If your coming to the show, I hope to see you there. You can register for the World of Concrete 2011 here.  Use source code A20 for free registration courtesy of the American Society of Concrete Contractors. 
Here is a 15 second commercial we will be running at the WOC on the shuttle busses and on screens at the show.

World of Concrete 2011 is January 17-21 in Las Vegas

Roadware will be exhibiting in the World of Concrete 2011.  This will be our 11th year at the show. Our booth will be in the South Hall S11847 at the Las Vegas Convention Center.

For free exhibits only registration, use source code A20 when filling out the online registration form. This code is courtesy  of the American Society of Concrete Contractors.

Click here to register for the World of Concrete.

DIY Network filming a segment in the Roadware booth at the World of Concrete 2009.

Polishing un-polishable Concrete

Polishing and honing concrete to smooth shiny surface is a great way to give an old warehouse floor new life. Sometimes, warehouse floors are too damaged and worn to make polishing practical. Floors that are full of cracks and spalls will require a large amount of grinding and polishing to achieve an acceptable surface. Roadware 10 Minute Concrete Mender™ may be used to restore the concrete surface and reduce the time and expense of heavy grinding. The Microdweling™ action of Roadware 10 Minute Concrete Mender™ can penetrate the surface of the cracks and spalls, fill in all the low spots, and make the floor ready for polishing.

Click on photos for a larger image.

Pitted, spalled and cracked surfaces may be unpractical to polish.

 

The first step is a light surface grinding to open up the cracks and remove any loose materials.

An initial grinding with metal resin pads reveals cracks and spalls.

Roadware 10 Minute Concrete Mender™ and fine silica sand mixed in bulk is troweled into the surface over the entire area and allowed to set.

Workers trowel Concrete Mender into place.

In about 10 – 30 minutes, the surface is polished using standard techniques. Roadware 10 Minute Concrete Mender™ will not gum-up polishing pads or smear into the surrounding concrete.

Surface polish using standard techniques.

After grinding, all pitting, cracks and spalls are filled and a smooth surface is quickly restored.

Concrete Mender repairs hold up perfectly during the polishing process.

After polishing, hardening and sealing, a beautiful polished floor is revealed.

Concrete Mender restored floor after polishing, hardening, and sealing.

Click here to learn more about polishing with Roadware 10 Minute Concrete Mender™

Special thank you to International Roadware Distributor Join K&C in Seoul, Korea for submitting this project.

Repairing Railings and Posts with 10 Minute Concrete Mender™.

How often have you run into this problem?  Industrial railings that have been split apart due to age, abuse, or weather damage. With a few special techniques, you can repair these problems with Roadware 10 Minute Concrete Mender™.

Clean the repair area with a wire brush or by sandblasting. Remove as much of the rust as possible. It is also a good idea to spray the the steel railing with a rust neutralizer.

 

Make a simple form out of blue foam board, and duct tape or most anything plastic. Do not use wood, Concrete Mender will permanently bond the wood to your railing base.I made that mistake years ago and had to chip, grind and sand the wood off the face of the concrete.

Make your repair by pouring 10 Minute Concrete Mender™ bulk mixed with sand in from the top. Allow to cure and finish the surface with a stone or grinder.

 

Add a quick coating of a latex cement coating and your finished. You may also make repairs around railings with Roadware Flexible Cement II™ if the railing is made aluminum and requires more thermal contraction and expansion properties.

Earthquake Crack Repair at Hope Alive Clinic in Haiti

“Kelton,

In March, you donated the Roadware kit to bind the cracks at the Hope Alive! Clinic in Haiti. THANK YOU FOR YOUR GIVING AND KIND HEART.

We went to the Atlantic City airport with the msds. They refused to allow us to bring the tubes on the plane. (they really didn’t know how to read the msds sheets either)

Anyway, we shipped the package via Philadelphia-container-Haiti. It arrived in time for our July 8th trip.

We brought along a Pastor who is also a “concrete guy”. He stated that he had never worked with a product that was so easy and did such a great job. As you can see in the attached photos, the fissure is completely sealed. As I mentioned in our phone conversation, the epi-center of the quake was only 6-7 miles from our clinic. We even have 2 sets of tubes left over!! (the neighbors will benefit)

I do not know how to say thanks but to just say “thanks” . Your kindness has made a difference with Hope Alive Clinics and the Haitian people. visit www.hopealiveclinic.org for more pictures of the teams and clinic activities.

If you are ever in the Philadelphia area, please look us up.

Again, many thanks and God bless you and your great company.

Frank Jacobs
Director, Hope Alive! Clinic Ministries”

Airport terminal deck repair after 5 years.

Here is a crack repair project at the CVG Airport in Cincinnati, Ohio. The upper terminal deck developed cracks parallel to the  construction joints. Roadware Flexible Cement II™ was used to repair the cracks in 2005. Here are some pictures of the project over the years.

Here is a photo of the CVG terminal deck as of June 2010.

 

Roadware Flexible Cement II™ was used the repair the crack on the right in 2005.  The crack on the left was repaired with Roadware 10 Minute Concrete Mender™ for comparison.

 

Finished repairs in 2005. Roadware Flexible Cement II™ on the left. Roadware 10 Minute Concrete Mender™ on the right.

 

Repairs as they appeared in 2006 after one year on service. Both are holding well. The Roadware 10 Minute Concrete Mender™ on the right shows yellowing, but is still performing well. The Flexible Cement II™ is slightly lighter on color, but looks perfect.

 

Here is the same repair in June 2010. After 5 years on service, everything looks good.

This is a close-up shot of the Flexible Cement II™ after 5 years of service. The repair is still holding like the day it was installed. Roadware Flexible Cement II™ is a good choice for outdoor repairs in structural concrete. The semi-flexible properties strike a good balance between road toughness and just the right amount movement absorption.

Concrete repair under decorative coatings.

The advances in decorative concrete coating and finishes for patios, sidewalks, driveways and pool decks are amazing. All of these systems have one common element. They are all affected by the condition of the concrete underneath. We recommend and use Roadware Concrete Mender™ Off-white to repair cracks, spalls and surface defects prior to decorative concrete treatments and coatings.  Off-white Mender is just like the Roadware 10 Minute Concrete Mender™ except it cures to a neutral off-white color that has less chance of affecting the color of the decorative coatings applied over the repairs.  Take a look at the project below.

P5101449

Here is a church with a spalled and rough looking entrance.

 

Prior repair materials were removed revealing worn, but sound concret

Concrete Mender Off-white

Roadware Concrete Mender™ Off-white and sand mixed in bulk is applied and troweled smooth. The material appears brown due to the brown colored manufactured sand added to the mix.

 

 Cracks are cleaned and repaired with cartridge applied Roadware Concrete Mender™ Off-white and sand.

After about 15 – 30 minutes, the repairs are ground smooth and flat. The concrete is now ready to accept most types of decorative concrete treatments.

 

NC4

Roadware  Concrete Mender™ Off-white is compatible with most high-build overlay or coating systems. It is also recommended by several top coating system manufacturers.

 

Gravity Crack Injection

UPDATE: See: Concrete Mender™ Full Depth Crack Injection

Roadware 10 Minute Concrete Mender™ is an excellent choice for repairing full depth concrete slab cracks. The very low viscosity of less than 8 cps and the exclusive Microdoweling™ penetration properties of the material allow it to flow deep into cracks. The procedure below illustrates Microdoweling™ in action.  The Concrete Mender will restore aggregate interlock and will allow dynamic load transfer under heavy traffic. The expense and mess of pressure injection with epoxy can be avoided.Here is a parking deck project located in the North Eastern United States. Hairline cracks run 9-12 inches deep through the deck slab. The contractor drilled 1 1/2 inch holes, 2-3 inches deep into the hairline cracks approximately every 18 inches. Inspection from the floor below reveals full penetration without pumps or ports. Engineers tell us that Roadware Microdoweling™ is quicker and more cost effective than epoxy injection.  The results speak for themselves.

Drilled concrete deck

 

drilled crack in parking deck

 

Gravity crack injection parking deck

 

concrete cracks gravity injection