Category Archives: decorative concrete repair

Vertical Wall Repair at Club Warehouse Store

Use Roadware 10 Minute Concrete Mender™ and sand to repair damaged concrete block walls in an hour or less. Sent in by Dave Wilson at Myspec Integrated Concrete Repair Group in Georgia.  770-335-9123 Roadware 10 Minute Concrete Mender™ is great for repairing cracks and spalls in floors. This ultra-low 8cps viscosity material gravity flows deep into concrete and makes repairs from the bottom up.  To repair a holes in a block wall, mix the Concrete Mender™ with fine silica sand to make a trowel-able mortar.

 Step 1: Prepare the area and remove any loose block, paint or dirt.

 

 

Step 2: Mask off the area like shown. In a clean bucket, mix one part AB blended Concrete Mender with 3 parts sand to make a stiff mortar and trowel into the repair area. You may want to tape a plastic sheet over the repair area to hold the Concrete Mender mixture in place while it cures for 10 minutes. See bulk mixing instructions here.

 

Step 3: After approximately 10 minutes depending on the ambient temperature, pull the masking and blend in the repair with a rubbing brick.

 

Step 4: Roadware 10 Minute Concrete Mender™ can be painted as soon as it cures.  Paint the repair area to match the surrounding wall.

With Roadware 10 Minute Concrete Mender™ you can do a job in less than an hour that used to take two days. No more waiting for hours or days while traditional cement based materials to set and cure.

Here is a video of using Roadware 10 Minute Concrete Mender™ to repair cracks in concrete or block walls.

 

 

Repairing Cracks in Driveways and Patios Updated

One of the most common calls we get is asking how to repair a crack in a driveway or patio.  We designed Roadware MatchCrete™ Clear with this in mind.  Roadware MatchCrete™ Clear is a UV stable clear polyurethane hybrid that makes effective repairs to most exterior concrete surfaces.  By simply leaving the repair clear, the color of the surrounding concrete shows throughout the repair.

The first step to a good looking crack repair is to rout-out or cut the repair open with a diamond blade grinder.  You only have to go about 1/4″ x 1/4″. This will create a recess for the material to rest as it soaks down further into the crack.  Skipping this step will allow the material to flow uncontrollably on the surface and will create a messy looking repair.

 

Apply cartridge mixed MatchCrete™ Clear directly to the crack. Small amounts of silica or quartz sand can be added to keep the material from flowing out the bottom of the slab.  If necessary, matching colored sand can be used to match colored concrete areas. Fill the crack to slightly below grade to prevent material from flowing on to the surface of the concrete.

After a year of service, the repair above still looks good.  Please note, MatchCrete™ Clear is not a soft expansion joint material and should not be used in joints that are designed to move.  Always give careful consideration as to why the concrete cracked in the first place and what the concrete is expected to do in the future before making repairs of this nature.

UPDATE:
September, 2013
We have a new video for driveway hairline crack repair:

Freezer threshold repair with Roadware 10 Minute Concrete Mender™.

Freezer, chiller and cooler thresholds have been an ongoing challenge to floor repair contractors and the USDA since the 1950’s. Recognizing the need to keep refrigerated and frozen food storage areas clean and sealed so they will not harbor lichen, fungus and pests, the USDA has issued zero tolerance guidelines for floor cracks and spalls in all food processing and refrigerated food lockers. Unsealed and opened joints also come under the watchful eye of those charged with keeping America’s food supply safe. Because thresholds are freezing cold on one side and at room temperature on the other, the thermal stress on the concrete is unrelenting and unforgiving. Couple this with forklift and wheeled cart traffic and you have a formula for disaster.

 

Fortunately, 10 Minute Concrete Mender™ has become the accepted repair material for these very harsh conditions. The agency itself is forbidden from recommending one product over another, but the personal choice among active USDA inspectors is Roadware 10 Minute Concrete Mender™. It’s thin, it gets in, it won’t pop out.

Some minimal prep work is required when working in the cold. Have the cracks and spalls as clean and dry as possible. This may not be easy, but it’s a step professionals know better than to ignore. Next, apply Mender to the base and sidewalls to seal off any free moisture movement into the repair area. Immediately follow by filling the spalled area or crack, almost to the top, with manufactured sand or approved quartz. Flood the sand to refusal, making sure the Mender saturates each grain. For larger areas, a bulk mixed mortar of Mender and sand may be easier to handle and install. Keep all materials at room temperature or warmer to speed up cure time. Even then, one should plan on an hour or more if temperatures are extreme. However, since all conditions vary, onsite testing is the best way to insure the time at which freezer floors and thresholds will be traffic-ready. Contractor field reports are very solid in reporting that 10 Minute Concrete Mender is the only thing that works in these tough repair situations. Click here for step by step bulk application instructions.

 

1. Remove existing concrete to wood base.

2. Saw key-way at a 45° downward angle on the cold side of the

threshold toward the freezer.

3. Using a diamond shaped pattern, drive sheet rock screws into

the base leaving 3/8″ of the screw sticking up, to act as a

dowel pin for the finishing lift of 10 Minute Concrete

Mender and sand aggregate.

4. Place 10 Minute Concrete Mender to grade. When fully cured

(about an hour at 32F, 0C) sawcut the warm side joint and fill

with Roadware Flexible Cement II™.

5. Reopen to traffic when Flexible Cement II is fully cured.

Continue reading Freezer threshold repair with Roadware 10 Minute Concrete Mender™.

Using Roadware MatchCrete™ Clear to repair cracks on the historic Stone Arch Bridge.

This week the City of Minneapolis used Roadware MatchCrete™ Clear to repair cracks in the exposed aggregate walkway surface on the Stone Arch Bridge in Minneapolis, Minnesota.   The Stone Arch Bridge is unique to the Mississippi River and features 23 arches, is 2100 feet long and 28 feet wide.

The bridge was built by railroad baron James J. Hill in 1883 and served as a working railroad bridge until 1965.  Today the bridge is mostly used by walkers and bicyclists.  The bridge also hosts many festivals and public events in the summer months.

In preparation for the summer festival season, City of Minneapolis crews used Roadware MatchCrete™ Clear to repair cracks in the exposed aggregate walkway surface. MatchCrete™ Clear is combined with matching rock to repair cracks and restore a consistent walking surface.

The process begins with routing out the cracks with a dry diamond blade
to remove loose dirt and debris. Clean and dry matching stone is placed
into the crack up to surface level.

Matching stone is added up to the surface level

Next, two-part blended MatchCrete™ Clear is poured into the repair up to the surface. This fills in all the voids between the stones and seals the crack.  MatchCrete™ Clear is a semi-ridged material that will support all kinds of traffic from pedestrians to industrial fork lifts.

MatchCrete™ Clear is added to the pre-placed stone

See video MatchCrete™ Clear application video below:

 

Repairs will have a, wet” look for a few months and will naturally dull over time. A clear coat sealing over the entire surface will off-set this effect.

MatchCrete™ Clear repair in exposed aggregate concrete.

In a few months, Repairs with MatchCrete™ Clear will dull and blend into the surrounding concrete.

Over time, repairs will become less shiny.

Update: June 24, 2012.

MatchCrete™ Clear repairs 18 days later.

 

I revisited the repairs on the bridge 18 days later. The surface has been sealed.  The repairs are performing as expected.

Roadware MatchCrete Clear is available is 50ml and 600ml cartridges and two gallon bulk kits.

 

Roadware MatchCrete™ Clear 71300 600ml Cartridge