Roadware Flexible Cement II Technical Data and Guide

Roadware Flexible Cement II™: Technical Data & Application Guide

Roadware Flexible Cement II™ is a two-component hydrophobic hybrid polyurethane system for maintaining control joints, repairing cracks, filling spalls, and bonding concrete to other materials.

Flexible Cement II™ provides a combination of toughness and controlled flexibility for low-movement concrete repairs. It can also be combined with specified aggregate to create a mix-in-place flexible polymer concrete.

Typical Physical Properties

PropertyTypical Value
ColorGray
Tensile Strength, ASTM D4121,726 psi
Ultimate Elongation, ASTM D412180%
Hardness70–80 Shore A
Service Movement±20%
Mixed Viscosity1,200 cps
Mixing Ratio1:1 by volume
VOC, MixedZero
Tack-Free Cure10–15 minutes at 21°C
Typical or approximate properties. Values should not be construed as specifications.

Recommended Applications

  • Repairing cracks 1/8 inch or larger subject to limited deflection, movement, dynamic loading, or thermal expansion and contraction.
  • Filling and protecting concrete control joints.
  • Repairing exterior spalls and pop-outs.
  • Forming and repairing bridge joint headers and nosings.
  • Filling potholes in concrete.
  • Bonding concrete, brick, tile, steel, asphalt, and wood.
  • Creating flexible polymer concrete when combined with specified aggregate.

Moisture and Environmental Performance

Flexible Cement II™ uses hydrophobic polyurethane chemistry designed to reduce interference from moisture during curing. This makes the system useful in moisture-prone environments including ground slabs, freezers, and containment areas.

Concrete surfaces should still be kept as dry as practical and properly prepared to achieve a good bond.

Control Joint Applications

Flexible Cement II™ can be used to fill and protect concrete control joints exposed to wheeled traffic while accommodating limited movement. Published technical data lists service movement at ±20%.

Joint sidewalls should be sound, clean, and free from contaminated repair materials. New concrete should be sufficiently cured so subsequent shrinkage does not exceed the movement capability of the material.

Important: Roadware Flexible Cement II™ is designed for low-movement concrete surfaces. It is not intended for use as a high-movement expansion joint material.

Flexible Polymer Concrete

For larger repairs, specified aggregate can be incorporated with Flexible Cement II™ to create a mix-in-place flexible polymer concrete.

Aggregate should be clean, dry, hard, and free from dirt, clay, and other contaminants. Aggregate size should be selected according to the dimensions and depth of the repair.

This method extends Flexible Cement II™ into larger-volume applications such as spalls and bridge joint repairs where thermal or shock movement may be present.

Surface Preparation

Concrete should be clean and free from dirt, oils, dust, laitance, loose concrete, old repair materials, and other contaminants that could interfere with bonding.

Mechanical preparation methods can be used to remove unsound concrete and create a suitable bonding profile. Ice and frost should be removed before application.

Mixing

Flexible Cement II™ is a two-component material mixed at a 1:1 ratio by volume.

Cartridge material is metered and mixed through a static mixing nozzle using a dual-component application gun. Bulk Parts A and B must be thoroughly mixed at the proper ratio and placed immediately into the prepared repair area.

Cure and Return to Service

The published technical data lists a tack-free cure of approximately 10–15 minutes at 21°C (70°F). Repairs can typically be returned to heavy traffic in approximately 20 minutes at 70°F.

Cure rate is temperature dependent. Warmer material and concrete temperatures decrease cure time, while colder conditions increase cure time.

Packaging

  • 600 ml dual cartridges
  • 2-gallon kits
  • 10-gallon kits

Technical Summary

Roadware Flexible Cement II™ combines 1,726 psi tensile strength, 180% elongation, 70–80 Shore A hardness, ±20% service movement, rapid cure, and zero VOC when mixed in a polyurethane system designed for tough, low-movement concrete repairs.

Its combination of mechanical toughness and controlled flexibility makes Flexible Cement II™ well suited for cracks, control joints, spalls, bridge repairs, cold environments, and applications where concrete must be bonded to dissimilar materials.

Flexible Cement II™ is intended for low-movement repairs and should not be specified as a high-movement expansion joint sealant.

Frequently Asked Questions

What is Roadware Flexible Cement II™?

Roadware Flexible Cement II™ is a two-component hydrophobic hybrid polyurethane system designed for maintaining control joints, repairing cracks, filling spalls, and bonding concrete to other materials.

How quickly does Flexible Cement II™ cure?

Flexible Cement II™ has a typical tack-free cure time of 10–15 minutes at 21°C (70°F). Cure time varies with material and concrete temperature.

How much movement can Flexible Cement II™ accommodate?

Published technical data lists service movement at ±20% and ultimate elongation at 180%.

Can Flexible Cement II™ be used in control joints?

Yes. Flexible Cement II™ is designed for filling and protecting concrete control joints in low-movement applications.

Can Flexible Cement II™ be used in expansion joints?

No. Flexible Cement II™ is designed for low-movement concrete surfaces and is not intended for high-movement expansion joints.

Can Flexible Cement II™ be used for spall repair?

Yes. Flexible Cement II™ can be used for concrete spalls and pop-outs. For larger repairs, specified aggregate can be incorporated to create a mix-in-place flexible polymer concrete.

What materials will Flexible Cement II™ bond to?

Flexible Cement II™ bonds to concrete, brick, tile, steel, asphalt, and wood.

What is the mixing ratio for Flexible Cement II™?

Flexible Cement II™ is a two-component system mixed at a 1:1 ratio by volume.

Commercial and Industrial Concrete Repair Products