Tag Archives: underlayment

Ultimate Guide to Crack Repair Under VCT or Laminate

Fast Concrete Repair for Commercial and Retail Floors

Downtime matters when concrete repair is taking place beneath finished flooring. Traditional repairs can turn a relatively small flooring problem into an extended interruption.

The original application highlights the 10-minute cure of Roadware 10 Minute Concrete Mender as a way to reduce the repair schedule.

For retail stores, commercial facilities, and other occupied buildings, that speed can make it practical to repair the concrete substrate and replace the affected flooring within a much shorter maintenance window.

Why Cracks and Joints Show Through Finished Flooring

VCT and other resilient floor coverings follow the profile of the concrete substrate beneath them. When a concrete crack or control joint deteriorates, the defect can eventually become visible through the finished flooring.

The right repair approach depends on the condition of the concrete. A deteriorated control joint with relatively flat adjoining slabs can require a very different repair from a crack where slab curling or movement has produced a significant elevation difference.

Before replacing damaged flooring, identify and repair the concrete condition underneath.

Repairing control or contraction joints under VCT.
Repairing contraction joints under VCT.

Repairing Failed Control Joints Under VCT

When a spalled or deteriorated control joint is reflecting through the flooring and the adjoining concrete slabs are not curled, the repair can be relatively straightforward.

Remove the affected flooring to expose the concrete. Clean out the deteriorated control joint using an appropriate dust-collecting diamond grinder and remove loose material and debris.

Repair the prepared joint with Roadware 10 Minute Concrete Mender. After the repair has cured, grind the repaired area flush with the surrounding concrete and replace the floor covering.

This approach addresses the damaged concrete beneath the flooring rather than simply covering the joint again.

Control or contraction joints repaired with 10 Minute Concrete Mender™ under VCT.
Control or contraction joints repaired with 10 Minute Concrete Mender™ under VCT.

 

For curled and buckled slabs, a major retailer specifies this heavy duty solution. Moreover, this is the ultimate one-and-done repair.

crack-repair-concrete-mender-vct-flooring_03

Step 1: Remove the Floor Covering

Remove the VCT, ceramic tile, vinyl, or other flooring as necessary to expose the affected concrete.

 

crack-repair-concrete-mender-vct-flooring_06

Step 2: Saw Cut Along the Crack

Make parallel saw cuts along the affected crack. The original procedure specifies a depth of no less than 1.5 inches and ideally approximately 30% of the slab depth.

 

crack-repair-concrete-mender-vct-flooring_08

Step 3: Remove and Prepare the Concrete

Chip out the concrete between the saw cuts. Thoroughly clean the prepared repair area using a wire brush and vacuum to remove loose material and debris.

 

crack-repair-concrete-mender-vct-flooring_10

Step 4: Repair With Concrete Mender

Use Roadware 10 Minute Concrete Mender with sand to rebuild the prepared area to the finished grade. The underlying crack is also repaired with Concrete Mender as part of the procedure.

See Concrete Mender™ Bulk Application Instructions.

 

crack-repair-concrete-mender-vct-flooring_13

Step 5: Finish the Repair and Replace the Flooring

Finish the repaired concrete to the appropriate elevation and replace the floor treatment. The original procedure is designed to allow the repaired area to be reopened to traffic after completion.

Fix the Concrete Before Replacing the Flooring

When a crack or failed control joint is visible through VCT, vinyl, laminate, or tile, look beyond the floor covering. The condition of the concrete underneath should be evaluated and repaired before new flooring is installed.

For relatively flat slabs, that may mean cleaning and repairing a deteriorated control joint. For curled or buckled concrete, a deeper repair may be required to restore the affected area before the flooring goes back down.

Roadware 10 Minute Concrete Mender provides a fast-curing approach for repairing these underlying concrete conditions and preparing the floor for replacement flooring.

 

Concrete slab under wood floor crack repair.

Today I received several photographs of a large crack that developed under a hardwood floor in a slab-on-grade application. The crack buckled the hardwood flooring. The home owner consulted several contractors and engineers to solve the problem. No cost-effective solution could be found until Roadware contractor, Clay Kenny, (Manderville, Lousiana) arrived on the scene.

Using Roadware 10 Minute Concrete Mender™ and silica sand, Clay repaired the crack to full depth and re-bonded the slabs back together using Roadware’s Microdoweling™technology.

The repairs cured in just 10 minutes and Clay was on and off the job in just 3 hours. The home owner was amazed. Clay and 10 Minute Concrete Mender™ did what couldn’t be done. The hard wood flooring was re-installed and the floor was put back in service faster then anyone could imagine. This repair took nine 600ml cartridges of #80300 Roadware 10 Minute Concrete Mender™ and a 40 lbs bag of silica sand to complete. The Concrete Mender™ turned a flooring disaster into an opportunity.
Anyone in the concrete business knows that concrete can be unpredictable and even a well thought-out project can develop cracks. Some are minor, and some can cause a real problem. Roadware 10 Minute Concrete Mender™ can help make the problems manageable.