Tag Archives: CM

Emergency Repair at Service Station with Concrete Mender

Bill Neal of Neals Design recently repaired spalled and cracked concrete on the fly at a service station in Washington.  A customer had broken an ankle stepping out of a truck into the badly spalled concrete. Bill was able to make the repair in minutes, eliminating the safety hazard without major disruption to the service station.

Roadware 10 Minute Concrete Mender is your go to product for making long-lasting repairs with minimal downtime.  At 70 degrees F  or 21C, A Concrete Mender repair can be ready for heavy truck traffic in about 10 minutes.

Finished Concrete Mender repairs at a truck fuel station.
Finished Concrete Mender repairs ready for traffic.

The ultra low viscosity Concrete Mender mixes very easily with manufactured sand or quartz.  A tough and durable polymer concrete mortar can be mixed in a bucket by hand with simple tools. No expensive pumps or power mixers needed. See how it is done here. Concrete Mender™ Bulk Application Instructions

Product used:

Roadware 10 Minute Concrete Mender™ Two-gallon Kit #80020

Roadware 10 Minute Concrete Mender™ two gallon kit. Item #80020
Roadware 10 Minute Concrete Mender™ two gallon kit. Item #80020

How to buy.

Find out more.

Concrete Mender on the Busan Metro Line 4

The Busan Transportation Corporation uses Roadware 10 Minute Concrete Mender to repair the roll-way of Busan Metro Line 4 in South Korea. Metro Line 4 is a rubber-tired line with 14 stations and runs driverless with pneumatic tires on a 6.7 mile (10.8km) concrete track. Concrete Mender is used to structurally repair the cross joints in the track approximately every ten meters.

Concrete Mender is the right product for the job because it has a long service life and cures in about 10 minutes. This allows for minimal down time and keeps the Busan Metro Line 4 running on time with minimal service interruption.

Repair crews of a very limited repair window, The train operates approximately 20 hours per day from 5am to 1am the next day. That leaves a minimal amount of time for maintenance and repair operations. Crews have to be efficient and productive. The fast cure and rapid strength gain of 10 Minute Concrete Mender is well suited for these mission critical applications.

 

 

Having a smoother roll-way saves wear and tear on the rubber tires and reduces operating costs.  Roadware 10 Minute Concrete Mender will keep the Busan Metro Line 4 running smooth and efficiently for years to come.

Edward Cheon of Concrete Doctor in Seoul on the concrete roll way at Busan Metro Line 4.

 

Roadware 10 Minute Concrete Mender is a self-injecting structural polyurethane for the permanent repair of commercial floors, decks, slabs and surfaces. The exclusive Microdoweling™ action in Concrete Mender allows it to migrate past bond lines, restore aggregate interlock and make long lasting repairs.

Crack in concrete floor ready for repair with Roadware 10 Minute Concrete Mender.

 

Click here to request more information of find a local Roadware distributor.

Roadware 10 Minute Concrete Mender™ comes in 50ml or 600ml cartridges or two and ten gallon bulk kits.

 

Warehouse floors can be repaired and open for traffic in about 10 minutes after application.

 

Click here to request more information or find a local Roadware distributor.

Ultimate Guide to Crack Repair Under VCT or Laminate

Fast Concrete Repair for Commercial and Retail Floors

Downtime matters when concrete repair is taking place beneath finished flooring. Traditional repairs can turn a relatively small flooring problem into an extended interruption.

The original application highlights the 10-minute cure of Roadware 10 Minute Concrete Mender as a way to reduce the repair schedule.

For retail stores, commercial facilities, and other occupied buildings, that speed can make it practical to repair the concrete substrate and replace the affected flooring within a much shorter maintenance window.

Why Cracks and Joints Show Through Finished Flooring

VCT and other resilient floor coverings follow the profile of the concrete substrate beneath them. When a concrete crack or control joint deteriorates, the defect can eventually become visible through the finished flooring.

The right repair approach depends on the condition of the concrete. A deteriorated control joint with relatively flat adjoining slabs can require a very different repair from a crack where slab curling or movement has produced a significant elevation difference.

Before replacing damaged flooring, identify and repair the concrete condition underneath.

Repairing control or contraction joints under VCT.
Repairing contraction joints under VCT.

Repairing Failed Control Joints Under VCT

When a spalled or deteriorated control joint is reflecting through the flooring and the adjoining concrete slabs are not curled, the repair can be relatively straightforward.

Remove the affected flooring to expose the concrete. Clean out the deteriorated control joint using an appropriate dust-collecting diamond grinder and remove loose material and debris.

Repair the prepared joint with Roadware 10 Minute Concrete Mender. After the repair has cured, grind the repaired area flush with the surrounding concrete and replace the floor covering.

This approach addresses the damaged concrete beneath the flooring rather than simply covering the joint again.

Control or contraction joints repaired with 10 Minute Concrete Mender™ under VCT.
Control or contraction joints repaired with 10 Minute Concrete Mender™ under VCT.

 

For curled and buckled slabs, a major retailer specifies this heavy duty solution. Moreover, this is the ultimate one-and-done repair.

crack-repair-concrete-mender-vct-flooring_03

Step 1: Remove the Floor Covering

Remove the VCT, ceramic tile, vinyl, or other flooring as necessary to expose the affected concrete.

 

crack-repair-concrete-mender-vct-flooring_06

Step 2: Saw Cut Along the Crack

Make parallel saw cuts along the affected crack. The original procedure specifies a depth of no less than 1.5 inches and ideally approximately 30% of the slab depth.

 

crack-repair-concrete-mender-vct-flooring_08

Step 3: Remove and Prepare the Concrete

Chip out the concrete between the saw cuts. Thoroughly clean the prepared repair area using a wire brush and vacuum to remove loose material and debris.

 

crack-repair-concrete-mender-vct-flooring_10

Step 4: Repair With Concrete Mender

Use Roadware 10 Minute Concrete Mender with sand to rebuild the prepared area to the finished grade. The underlying crack is also repaired with Concrete Mender as part of the procedure.

See Concrete Mender™ Bulk Application Instructions.

 

crack-repair-concrete-mender-vct-flooring_13

Step 5: Finish the Repair and Replace the Flooring

Finish the repaired concrete to the appropriate elevation and replace the floor treatment. The original procedure is designed to allow the repaired area to be reopened to traffic after completion.

Fix the Concrete Before Replacing the Flooring

When a crack or failed control joint is visible through VCT, vinyl, laminate, or tile, look beyond the floor covering. The condition of the concrete underneath should be evaluated and repaired before new flooring is installed.

For relatively flat slabs, that may mean cleaning and repairing a deteriorated control joint. For curled or buckled concrete, a deeper repair may be required to restore the affected area before the flooring goes back down.

Roadware 10 Minute Concrete Mender provides a fast-curing approach for repairing these underlying concrete conditions and preparing the floor for replacement flooring.